Công ty TNHH Sao Đỏ Việt Nam

Giỏ hàng 0

Tổng : 0 đ

Trang chủ >> Thiết bị Đo lường >> Sản xuất công nghiệp >> Máy đo & kiểm tra rung >> Thiết bị thử rung >> Loại tiết kiệm năng lượng

EM-series（ECO-Shaker)

Model:
Tình trạng: Liên hệ

Control electricity consumption automatically depending on test conditions

ECO-Shaker realized full-scale energy-saving vibration test that was difficult in conventional shakers. It enables vibration test operated at automatically optimized electricity consumption by inputting usual test definition.

Bảo hành: Chưa có thông tin bảo hành

Giá bán: Liên hệ

Đặt hàng

Khung giờ giao hàng từ 8h00 - 18h00 hàng ngày.
Sản phẩm chính hãng, cung cấp CO & CQ.
Bảo hành miễn phí 12 tháng với máy chính.
Giá trên chỉ áp dụng đối với mặt hàng có sẵn.
Đối với mặt hàng không có sẵn sẽ tính thêm phí vận chuyển.

Gửi email yêu cầu báo giá: info@redstarvietnam.com Tất cả các ngày trong tuần

Đặc tính nổi bật
Thông số kỹ thuật
Ứng dụng
Nhận xét

Always developing vibration test systems

IMV's dynamic simulation systems have been developed with "intelligence" in mind and endeavour to support customers testing. The new Eco technology has been used in the IMV range.

Complicated settings are not needed.

Electricity consumption might be managed manually on electrodynamic systems, but this could be quite difficult for the system operator to optimise the consumption due to payload and test conditions. Our ECO-Shaker can achieve optimisation of power consumption refering to payload conditions.

You can confirm the result of reduction of CO2 and electricity consumption at glance.

By combination with IMV vibration controller ‘K2’ , ECO-shaker system will confirm real-time electricity consumption during testing. It was never available by conventional systems. Power consumption can be reported numerically after each test.

You can expect improvement of laboratory environment.

Noise to be expected from the conventional test system will give limitaion to installation place selection. Our ECO-Shaker can suppress the noise level by controlling the engine blower at optimised speed. Optimum control of the cooling system will reduce power consumption and noise level refering to test conditions.

We will contribute to well being of society from both sides of quality and environmentt

By Clean Development Mechanism (CDM) in January 2008 and revision of Rationalisation in Energy Use law in April 2009 were introduced in Japan, all enterprises have been obliged to be more energy efficient. ECO-Shaker promotes reduction of costs and CO? by saving electricity consumption, costs, and consequently contributes to society.

Real automatic energy saving driving

Complicated settings are not needed.

ECO-shaker is a electrodynamic vibration test system which automatically optimize output of power amplifier, power input to vibration and cooling blower rotation speed refering to payload and test conditions. So, complicated manual settings are not needed anymore. Since it is real automatic control according to working environment conditions, "drastic change in output levels due to change of test sample characteristics during the test", "temperature up in system caused by rising heat during operation" etc.. even if those phenomenon happen, it is possible to keep operation without stopping the test.

You can confirm reduction of CO2 and electricity consumption at real-time.

Comparison of electricity consumption with conventional shaker

The less system output, the more saving-energy you can expect.

Figures are calculated by comparing with conventional system of same sine force rating. Results may vary for system models, test conditions.

Operation of ISM-EM (Power consumption)

Power consumption on conventional vibration systems would require manual calculation refering to test conditions. ISM-EM technology of the ECO-Shaker can automatically control the output of the power amplifier, force generation of the shaker, and rotation speed of the cooling blower to achieve best efficiency refering to test conditions.

Correspondence to existing system [Retro fit]

Saving energy by ISM-EM technology can be applied on existing IMV vibration test systems by adding the ISM-EM unit and some calibrations. Contact us for further information and delivery.

	System Model		EM2201	EM2301	EM2401	EM2501	EM2502	EM2551	EM2601
System Specifications	Freq. Range(Hz)		0～3300	0～3000	0～2600	0～2500	0～2500	0～2600 ^*5)	0～2600 ^*5)
	Rated Force	SINE(kN)	8	16	24	32	40	49	54
		RANDOM(kNrms)^*2)	8	16	24	32	40	49	54
		SHOCK(kN)	16	32	48	64	80	98	108
	Max. Acc.	SINE(m/s²)	1250	1250	1200	914	1142	907	1000
		RANDOM(m/s²rms)	875	875	840	640	800	635	700
		SHOCK (m/s²)	2500	2500	2400	1828	2284	1814	2000
	Max. Vel.	SINE(m/s)	2.2	2.2	2.2	2.2	2.2	2.2	2.2
	Max. Vel.	SHOCK(m/s)	2.2	2.2	2.2	2.2	2.2	2.2	2.2
	Max. Dsp.	SINE(mmp-p)	51	51	51	51	51	51	51
	Max. Dsp.	Max. TRAVEL (mmp-p)	60	64	68	68	68	64	64
	Max. Load.(kg)		200	300	400	600	600	1000	1000
	Power Requirements(kVA)^*1)		16.4	26	36	51	57	80	83
Vibration Generator	Model		i220	i230	i240	i250	i250	i255	i260
	Armature Mass(kg)		6.4	12.8	20	35	35	54	54
	Armature Diameter(φmm)		190	200	290	440	440	446	446
	Allowable eccentric moment (N･m)		294	700	850	1550	1550	1550	1550
	Dimensions(mm)W×H×D		1020x 903x 550	1124x 957x 860	1234x 997x 890	1463x 1187x 1100	1463x 1187x 1100	1527x 1196x 1100	1527x 1196x 1100
	Mass(kg)		900	1500	2000	3000	3000	3500	3500
Power Amplifier	Model		SA1M- i20EM	SA2M- i30EM	SA3M- i40EM	SA4M- i50EM	SA5M- i50EM	SA7M- i55EM	SA7M- i60EM
	Max. Output(kVA)		10	20	29	40	50	58	64
	Dimensions(mm)W×H×D		580x 1750x 850	580x 1750x 850	580x 1750x 850	580x 1950x 850	580x 2100x 850	1160x 1950x 850	1160x 1950x 850
	Mass(kg)		330	350	460	900	930	1400	1400
Controller	Vibration Controller		See Vibration Controller K2
Cooling	Cooling Method		Air cooling
	Blower	Dimensions(mm) W×H×D	492x 1128x 627	606x 1315x 844	707x 1531x 896	1057x 1841x 1078	1057x 1841x 1078	1328x 2140x 1033	1328x 2140x 1033
	Blower	Mass(kg)	70	125	210	250	250	370	370

*1） Power supply required is 3-phase 200/220/240/380/400/415/440V,50/60Hz. Voltage Down Transformer (Step-down transformer) is required for other voltage.
*2） Rated force of RANDOM follow the ISO5344 standard. Please contact us for further information on RANDOM force conditions of each system.
*3） Each value of specification indicates maximum power of the system. In the case of a long hours of test, it needs to be operated less than 70% of maximum power.
(The continuous use could be the cause of a premature failure.)
*4） In the case of RANDOM durability test, please set the test definition of the peak value of acceleration waveform to be operated less than 1400 m/s2.
*5） In the band of more than 2000Hz, excitation force pitches at the rate of -12dB/oct.
*6） Frequency range values vary according to sensor and signal generator.
*7） Mass and size can change in CE-support system.

Specifications (Large Displacement Type)

	System Model		EM2305	EM2405	EM2505	EM2506	EM2555	EM2605
System Specifications	Freq. Range(Hz)		0～3000	0～2400	0～2200	0～2200	0～2600 ^*5)	0～2600 ^*5)
	Rated Force	SINE(kN)	16	24	35	40	49	54
		RANDOM(kNrms)^*2)	16	24	35	40	49	54
		SHOCK(kN)	40	55	70	80	98	108
	Max. Acc.	SINE(m/s²)	941	923	777	888	777	857
		RANDOM(m/s²rms)	658	646	544	622	544	600
		SHOCK (m/s²)	2352	2115	1555	1777	1555	1714
	Max. Vel.	SINE(m/s)	2.4	2.4	2.4	2.4	2.4	2.4
	Max. Vel.	SHOCK(m/s)	2.4	2.4	2.4	2.4	2.4	2.4
	Max. Dsp.	SINE(mmp-p)	100	100	100	100	100	100
	Max. Dsp.	Max. TRAVEL(mmp-p)	120	120	120	120	116	116
	Max. Load.(kg)		300	400	600	600	1000	1000
	Power Requirements(kVA)^*1)		28	38	53	57	82	86
Vibration Generator	Model		J230	J240	J250	J250	J255	J260
	Armature Mass(kg)		17	26	45	45	63	63
	Armature Diameter(φmm)		200	290	440	440	446	446
	Allowable eccentric moment (N･m)		700	850	1550	1550	1550	1550
	Dimensions(mm)W×H×D		1124x 1079x 850	1234x 1145x 890	1463x 1301x 1100	1463x 1301x 1100	1527x 1319x 1100	1527x 1319x 1100
	Mass(kg)		1800	2400	3500	3500	4100	4100
Power Amplifier	Model		SA3M- J30EM	SA4M- J40EM	SA5M- J50EM	SA6M- J50EM	SA7M- J55EM	SA7M- J60EM
	Max. Output(kVA)		23	34	50	57	64	70
	Dimensions(mm)W×H×D		580x 1750x 850	580x 1750x 850	580x 2100x 850	580x 2100x 850	1160x 1950x 850	1160x 1950x 850
	Mass(kg)		380	490	930	960	1400	1400
Controller	Vibration Controller		See Vibration Controller K2
Cooling	Cooling Method		Air cooling
	Blower	Dimensions(mm) W×H×D	606x 1315x 844	707x 1531x 896	1057x 1841x 1078	1057x 1841x 1078	1328x 2140x 1033	1328x 2140x 1033
	Blower	Mass(kg)	125	210	250	250	370	370

*1） Power supply required is 3-phase 200/220/240/380/400/415/440V,50/60Hz. Voltage Down Transformer (Step-down transformer) is required for other voltage.
*2） Rated force of RANDOM follow the ISO5344 standard. Please contact us for further information on RANDOM force conditions of each system.
*3） Each value of specification indicates maximum power of the system. In the case of a long hours of test, it needs to be operated less than 70% of maximum power.
(The continuous use could be the cause of a premature failure.)
*4） In the case of RANDOM durability test, please set the test definition of the peak value of acceleration waveform to be operated less than 1400 m/s2.
*5） In the band of more than 2000Hz, excitation force pitches at the rate of -12dB/oct.
*6） Frequency range values vary according to sensor and signal generator.
*7） Mass and size can change in CE-support system.

Specifications (High Power Water Cooled Type)

	System Model		EMK0301	EMK0621	EMK0622	EMK0801	EMK1251	EMK1252	EMK2001	EMK2002
System Specifications	Freq. Range(Hz)		0～3000	0～2500	0～2500	0～2500	0～2500	0～2500	0～2000	0～2000
	Rated Force	SINE(kN)	30.8	49.0	61.7	80	100	125	160	200
		RANDOM (kNrms)^*2)	21.5	49.0	61.7	80	100	125	160	200
		SHOCK(kN)	61.6	98	123.4	160	200	250	320	400
	Max. Acc.	SINE(m/s²)	1000	1000	1000	1000	1000	1000	800	1000
		RANDOM (m/s²rms)	557	700	700	700	700	700	700	700
		SHOCK (m/s²)	2000	2000	2000	2000	2000	2000	1600	2000
	Max. Vel.	SINE(m/s)	1.8^*5)	2.0^*5)	2.0^*5)	2.0^*5)	2.0^*5)	2.0^*5)	2.0^*5)	2.0^*5)
	Max. Vel.	SHOCK(m/s)	1.8	2.0	2.0	2.0	2.0	2.0	2.4	2.4
	Max. Dsp.	SINE(mmp-p)	51	51	51	51	51	51	76.2	76.2
	Max. Dsp.	Max. TRAVEL (mmp-p)	58	60	60	59	62	62	86	86
	Max. Load.(kg)		500	1000	1000	1000	2000	2000	2000	2000
	Power Requirements (kVA)^*1)		49	76	87	100	150	170	270	300
Vibration Generatoer	Model		K030	K060	K060	K080	K125	K125	K200	K200
	Armature Mass(kg)		27	40	40	60	70	70	200	200
	Armature Diameter(φmm)		320	400	400	446	560	560	650	650
	Allowable eccentric moment (N･m)		980	980	980	1550	2450	2450	4900	4900
	Dimensions(mm) W×H×D		1100x 1090x 824	1380x 1085x 1000	1380x 1085x 1000	1595x 1050x 1200	1776x 1360x 1300	1776x 1360x 1300	2465x 1908x 1740	2465x 1908x 1740
	Mass(kg)		3000	3700	3700	5000	7000	7000	16000	16000
Power Amplifier	Model		EM4MM -K30	EM6MM -K60	EM8MM -K60	EM14HM -K80	EM18HM -K125	EM22HM -K125	EM26HM -K200	EM32HM -K200
	Max. Output(kVA)		33	43	60	100	98	124	256	320
	Dimensions(mm) W×H×D		580x 1950x 850	1160x 1950x 850	1160x 1950x 850	1740x 1950x 850	1740x 1950x 850	2320x 1950x 850	2900x 1950x 850	3480x 1950x 850
	Mass(kg)		950	1300	1350	2250	2400	3200	4000	4800
Controller	Vibration Controller		See Vibration Controller K2
Cooling	Cooling Method		Shaker:Water Cooling/Amp:Air Cooling
Cooling	Primary Cooling Water Supply (l/min)		195	260	260	390	390	390	520	520
Heat Exchanger	Dimensions(mm) W×H×D		580x 1700x 850	580x 1700x 850	580x 1700x 850	580x 1700x 850	580x 1700x 850	580x 1700x 850	950x 1900x 800	950x 1900x 800
Heat Exchanger	Mass(kg)		400	400	400	400	400	400	600	600

*1） Power supply required is 3-phase 200/220/240/380/400/415/440V,50/60Hz. Voltage Down Transformer (Step-down transformer) is required for other voltage.
*2） Rated force of RANDOM follow the ISO5344 standard. Please contact us for further information on RANDOM force conditions of each system.
*3） Each value of specification indicates maximum power of the system. In the case of a long hours of test, it needs to be operated less than 70% of maximum power.
(The continuous use could be the cause of a premature failure.)
*4） In the case of RANDOM durability test, please set the test definition of the peak value of acceleration waveform to be operated less than 1400 m/s2.
*5） If the tests (SWEEP or SPOT) need high velocity the maximum velocity value should be reduced to 1.4m/s.
In the case of continuous SINE test, at move than 1.4m/s, it may need optional cooling system, so please consult with us.
*6） Frequency range values vary according to sensor and signal generator.
*7） Mass and size can change in CE-support system.